Flue-less Gas Fireplaces

 

Flue-less Gas Fires are without a chimney and are therefore considerably more fuel efficient. The design of the fire is such that the amount of carbon monoxide/dioxide produced is minimised to make the fire safe to use without a chimney.

In the INFINITI gas fireplace range, with a uniquely designed combustion system, they reach heating efficiencies of close to 100%. This makes these flue-less fireplace units superb for the economical heating of large spaces. And of course the units are perfect for installation into rooms or houses without chimneys.

BUILT-IN UNITS

FLAME DANCER™

The Flame Dancer grates are Infiniti’s newer grates. They have a flame that exits the grate in a vertical sheet of flame about 100mm high, if left uncovered. The design of the burner creates a flame that dances, hence its name. If covered the flame effect will spread across more of the grate and give a more traditional look.

The Infiniti Flame Dancer grates were designed to give not only stunning modernistic looks but even more importantly, VERY low emissions.

These industry leading low emissions are very beneficial in terms of:

  • a virtually odourless grate
  • a very safe grate with the lower amounts of Carbon Monoxide/Dioxide produced
  • a more efficient grate as more of the carbon in the fossil fuel is converted in the combustion process to usable heat

Flame Dancer grates are available in the following fuel effects:

Burner uncovered

  • White or black stone chips around the burner
  • Natural white stones around the burner
  • Stainless Steel Base plate. This gives an amazing reflection of the dancing flame, fantastic for modern homes

Burner covered

  • White or black chips around the burner, natural white stones over the burner
  • Natural white stones around and over the burner

Heating Capacity

  • 700mm size Flame Dancer grates are available in either 5kw or 7kw heating capacities.
  • 1000mm size Flame Dancer grates are available in 10 Kw heating capacity.

Different Trims Can Be ordered separately in either black or stainless steel finish.

CONCEPT FLUE-LESS GAS

 
 

The Infiniti Concept Gas fire is designed to be hung on a wall, or with the addition of a top and bottom section, be installed as a modernistic mantle unit. Ideal for complementing today’s more modern architectural styles.

These units require no messy building work or costly alterations. Instead they simply bolt to the wall to give an easy and time saving installation, without the mess and disruption of building.

This Infiniti unit uses the tried & trusted NGC valve installed on all our gas fires. Conveniently located in the RHS panel of the unit for easy access.

The top and bottom sections of the mantle are available in a choice of 2 colours. If you want your own colour scheme these sections can be over painted by your installer to your individual requirements.

  • Available with Flame Dancer grate.

Heating Capacity

  • 5-7kw, 200-300 m³ depending on model chosen.

DROP IN GRATE – MODERN STYLING AT ITS BEST

 coz021210d-44_7

Our drop in grates are designed to simply drop into a hole in a slab, very much like a kitchen hob drops into the kitchen counter.

The slab can be made out of any non combustible material; concrete, granite, marble, etc. to enable you to make a fashion statement to suit your home.

It is imperative for the grate to function, that there is an adequate air supply to the underside of the slab. All our Drop in Grates are provided with a louvre for you to build into the brick structure to allow the required amount of air in.

  • Available as standard in 880, 1100, 1400 & 2000mm long units
  • Available as specials with variable length & depth
  • Available in black or brushed stainless steel
  • Black unit is supplied with natural white stones to enable you to cover the grate in stones if so desired
  • Grates can be fitted flush with slab surface or recessed into it to give different looks
  • Available with Flame Dancer grate

Heating Capacity

  • Standard Models 5-15kw 200-600m³
  • Special Models 10-15kw 400-600m³

CONVERSION GRATE

coz021210d-56

The easy way to convert an existing inefficient flued gas fire to a highly efficient flueless

These grates are designed to enable the easy conversion of an existing steel or brick fireplace into a flue-less gas fire. If you have an open wood or anthracite burning fire it is as simple as sealing up the chimney opening to prevent heat loss up the chimney, running gas to the fire and connecting up our flue-less grate.

No more lighting of fires, no more smoke smell in the house, no more cleaning out the ash. Simply large quantities of heat with the convenience of a flick of a switch.

If you have a flued gas fire it is even easier. Remove the flued grate, seal up the chimney flue and fit the flue-less grate to the existing gas line. Generally a 1 to 2 hour job.

Our flue-less grate is 3 times more efficient than most flued grates. That is either a lot more heat for your house at no extra cost or the same heat with a big reduction in running cost. Plus, you will be doing your bit for our environment by utilising our gas reserves in a more beneficial manner.

  • Available in 550, 700, 850 and 1050mm size
  • Available with Flame Dancer Grate

Heating Capacity

  • 5-10kw, 200-400m³ depending on model chosen.

FLAME DANCER™ ABSTRACTS

A range of flue-less gas fires developed by Infiniti Fires using their high tech Flamer Dancer grate.

The Flame Dancer grates are designed to give both stunning visual appeal as well as very low emissions, very important in a flue-less gas appliance.

These industry leading low emissions are very beneficial in terms of:

  • a virtually odourless grate
  • a very safe grate with lower amounts of Carbon Monoxide/Dioxide produced
  • a more efficient grate as more of the carbon in the fossil fuel is converted in the combustion process to useable heat.

Flame Dancer Abstract units are available with heating capacities of 200m³ or 300m³. The FD 200 unit is ideal for those smaller rooms from 60m³ upwards and the FD300 unit from 98m³ upwards.

Please specify the heating capacity required when ordering.

The bodies of these gas fires were designed to be different to the norm currently produced in South Africa. With innovative thinking about minimising steel waste and maximising look and heating capacity.

In line with the great abstract architects and painters of the last century who dared to be different, these units are designed to be both functional and aesthetically pleasing in a minimalist way. We have named our units after some of these great achievers.

Corbusier

The single and double sided Corbusier have a space saving 310mm depth, making them very easy to build into internal brick walls, whilst giving a very stylish appearance.

Picasso

The wall mounted Picasso unit, with it’s sleek contours, makes this a feature to be fitted onto a wall at the same height as a picture.

Designed to be retro-fitted after a wall is complete, by simply bolting it to the wall and connecting it to a gas supply. Ideal as a powerful heater in existing homes or newly built houses.

Cezanne

The single and double sided Cezanne units, designed to be freestanding units. An easy retro fit in existing homes.

Flame Dancer Grates are available in the following fuel effects:

Burner uncovered

  • Black Steel
  • White or black stone chips around the burner
  • Natural White Stones around the burner

Burner Covered

  • White or black stone chips around the burner with natural white stones over the burner
  • Natural white stones around and over the burner

The Picasso unit is supplied with a loose stone trim. This may be fitted if desired to retain any of the above coverings over the top of the unit.